HERION电磁阀运转中的问题资料有哪些？
般都是选型问题，者介质的属性出现了变化，导致HERION电磁阀部件及阀芯等，不能正常工作。用户可以重新确认电磁阀介质属性，或者配备合适的电磁阀型号产品。
HERION电磁阀阀芯损坏
般造成HERION电磁阀阀芯损坏的原因比如使用的介质属性和环境超过工作范围，或者电磁阀使用时间过长、操作不当而导致的。造成电磁阀芯故障的原因有很多，多是因为长期的使用，超过了使用年限，寿命到期，或者因为操作和使用不正当造成的非正常损坏。正确的阀芯故障检测方法是检测是否是使用寿命到期，其次是介质的属性和环境有没有在高压蒸汽电磁阀产品的工作范围里面，zui后是检测有没有堵塞的情况。
HERION电磁阀在使用的过程中，应注意该的压力工作范围，超过工作范围的工作压力会损坏电磁阀，造成泄漏以及给用户带来损失。如果有压力异常或超过电磁阀的实际工作范围，请立即关闭电磁阀的前后手动阀，停止电磁阀的工作。
HERION电磁阀的密封是整个电磁阀的重要部件之，应确保电磁阀密封的。并保持电磁阀密封内部的清洁。
由于HERION电磁阀系列的型号多样，每个型号都有自己的特性和工作范围。对于新用户来说，可以参考厦门乾球自动化销售人员和技术人员的介绍，选择更合适您的。
机械设备在工作的状态下，应避免松动的情况发生，以减少机械振动，降低机械损坏，延长电磁阀使用寿命。
对于工作在特殊环境的电磁阀，例如接近水源，工作环境杂物过多等，应为电磁阀配备合适的防护设备。电磁阀的使用寿命，在用户方面的维护和使用操作也会造成定的影响。而选择合适的电磁阀型号也很重要，用户们在购买力典电磁阀的时候，请尽量提供详细的要求和工作条件，介质属性等，这样才可以选择更加合适用户的电磁阀。
以下是参考译文：
1, solenoid valve coil burned out, can remove the solenoid valve wiring, measured with a multimeter, if open, the solenoid valve coil burned. Moisture causes the coil, magnetic flux leakage caused by bad insulation, causing the coil current is too large to burn. Countermeasures: so to prevent flood water from entering the solenoid valve. In addition, excellent spring, reaction force is too large, too few coil turns, the suction can not make the coil burnt. Emergency treatment, can be "0" bit hit "1" bit manual button on the coil from the normal work, makes the valve open. 2, solenoid valve head loose or thread off wiring, electric solenoid valve shall be fastened thread:, countermeasures. 3, solenoid valve stuck. Slide valve sleeve and spool valve clearance Anhui SECCO environmental protection science and technology supply is very small (less than 0.008mm), are generally single assembly, when a mechanical impurities into or too little lubricant, it is easy to get stuck. Countermeasures: can hold into the wire hole from the head to make it bounce. The fundamental solution is to remove the valve, remove the spool and spool cover, clean with CCI4, making flexible movement in the valve spool sleeve. Demolition should pay attention to the assembly sequence and location of the external connection of each component, in order to re assembly and wiring is correct, also check whether the plug hole injector lubricator, lubricating oil is sufficient. 4, leakage. Lack of air pressure can cause leakage, making enforcement difficult to open and close the valve, the reason is the slide valve gasket damage or wear caused by several cavity channeling gas. Countermeasures: in dealing with the electromagnetic valve failure switching system, should select the appropriate time, such as the solenoid valve is energized when dealing with, if not processed in a gap switch, switching system can be suspended, disposed of